|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Slotted Optical Switch OPB817Z Features: * * * * 0.20" (5.08 mm) wide gap, 0.86" (21.84 mm) deep slot 24" (609 mm) 26 AWG wires Dust protection Two mounting tabs Product Photo Here Description: The OPB817Z slotted switch consists of an infrared emitting diode and a NPN silicon phototransistor mounted in an opaque housing with clear windows for dust protection. Switching of the phototransistor occurs whenever an opaque object passes through the slot. The OPB817Z has an 0.86" (21.844 mm) deep slot allowing for a longer reach of the optical center line from the mounting plane. The phototransistor internal apertures are 0.10" x 0.06" (0.25 mm x 1.52 mm) on the sensor side ("S") and 0.05" x 0.06" (1.27 mm x 1.52 mm) on the emitter side ("E"). Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications: * Non-contact object sensing * Assembly line automation * Machine automation * Equipment security * Machine safety Ordering Information Part Number OPB817Z Description Slotted switch 1 4 Color/ Red-1 Black-2 White-3 Green-4 Description Anode Cathode Collector Emitter 2 3 RoHS OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.2 01/06 Page 1 of 3 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Slotted Optical Switch OPB817Z Absolute Maximum Ratings (TA=25C unless otherwise noted) Storage & Operating Temperature Range Lead Soldering Temperature [1/16 inch (1.6mm) from the case for 5 sec. with soldering iron] Input Diode Forward DC Current Peak Forward Current (1 s pulse width, 300 pps) Reverse DC Voltage Power Dissipation (2) (1) -40 C to +85 C 260 C 50 mA 3A 2V 100 mW Output Phototransistor Collector-Emitter Voltage Emitter-Collector Voltage Collector DC Current Power Dissipation(2) 30 V 5V 30 mA 100 mW Electrical Characteristics (TA = 25C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (see OP140 for additional information) VF IR Forward Voltage Reverse Current 1.8 100 V A IF = 20 mA VR = 2 V Output Phototransistor (see OP552 for additional information) V(BR)(CEO) V(BR)(ECO) ICEO Coupled IC(ON) VCE(SAT) Notes: (1) (2) (3) (4) (5) (6) (7) Collector-Emitter Breakdown Voltage Emitter-Collector Breakdown Voltage Collector-Emitter Leakage Current 30 5 - - 100 V V nA IC = 1 mA, IF = 0, EE = 0 IE = 100 A, IF = 0, EE = 0 VCE = 10 V, IF = 0, EE = 0 On-State Collector Current Collector-Emitter 1.0 - - 10.0 0.4 mA V VCE = 5 V, IF = 20 mA IC = 100 A, IF = 20 mA RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 1.67 mW/C above 25 C. All parameters were tested using pulse techniques. Lead spacing of 0.220" (5.59 mm) or 0.320" (8.13 mm) is available. Leads are 0.20" square (5.08 mm) and 0.425" long (10.80 mm), which is the minimum. Methanol or isopropanol are recommended as cleaning agents. Plastic housing is soluble in chlorinated hydrocarbons and ketones. Spray and wipe; do not submerge. Polarity is denoted by color of housing top: LED (gray or clear), sensor (black). Clear dust protection. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A .2 01/06 Page 2 of 3 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Slotted Optical Switch OPB817Z OPB817Z - Flag Next to Emitter 1.20 1.20 OPB817Z - Flag Next to Sensor 1.00 1.00 Typical IC(ON) Response (mA) Typical IC(ON) Response (mA) 0.80 0.80 0.60 0.60 0.40 Right to Left 0.40 0.20 Left to Right Top to Bottom 0.20 Right to Left Left to Right Top to Bottom 0.00 0.00 0.05 0.10 0.15 0.20 0.25 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) Displacement Distance (inches) OPB817Z - Flag in Middle of Slot 1.20 Test Schematic 1.00 Typical IC(ON) Response (mA) 0.80 0.60 0.40 Right to Left 0.20 Left to Right Top to Bottom 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.2 01/06 Page 3 of 3 |
Price & Availability of OPB817Z |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |